Manufacturing/Production

Permalink Gallery

Trimeca – Jorge Pradella

Trimeca – Jorge Pradella

, ,

Location: Houston, TX
Total sq.ft.: 7,500
Roof slope: 1:12
Roof panels: PBR
Wall panels: PBR
Special features: This building features a top running crane.
Builder: Jorge Pradella
Erector/Roofing Contractor: Genesis Metal Building Erectors, LLC
Designer/Architect: BM Design, LLC

Permalink Gallery

Community Impact Press Building – Aday & Associates

Community Impact Press Building – Aday & Associates

,

Location: Pflugerville, TX
Total sq.ft.: 35,105
Roof slope: 1/4:12
Roof panels: Ultra-Dek
IMP Wall panels: Tuff-Wall
Special features: Building A features a recessed wall and roof at sidewall entrance along with parapets at endwalls. Building B features a skewed sidewall.
General Contractor: Aday & Associates
Erector/Roofing Contractor: R-Squared Construction
Designer/Architect: PLACE Designers

seanic-ocean-systems
Permalink Gallery

Seanic Ocean Systems – Lonestar Construction

Seanic Ocean Systems – Lonestar Construction

,

The Seanic Ocean Systems building offers solutions for deep-water exploration in Katy, Texas. Lonestar Construction was the project’s builder, Steve Husmann was the project’s architect and Loy Construction served as the erector. The building utilizes both gable symmetrical and single slope framing. Mid-West’s PBR and Ultra-Dek® roof panels were specified components for the project, in addition to Mid-West’s PBR wall panels. Stucco and masonry were used on the office building’s exterior for favorable aesthetics. The building also holds a large test pool similar to those at NASA and a crane with a 20-ton crane load.

southern-star-brewery
Permalink Gallery

2015 President’s Choice – Southern Star Brewery – Huffco Services

2015 President’s Choice – Southern Star Brewery – Huffco Services

, , ,

Southern Star Brewery in Conroe, Texas is a regional brewer of craft beers. Huffco Services, Inc. served as the project’s builder and Huffco’s very own Chris Fritsche served as head architect. The brewery features a gable symmetrical framing system with PBR roof panels. PBR and PBU wall panels were also specified components. The 27,000 square foot brewery also features a 100′ Clear Span frame designed to house large beer brewing equipment.

burkhart-compression
Permalink Gallery

Burkhart Compression – Lonestar Construction

Burkhart Compression – Lonestar Construction

, ,

Located in Waller, Texas, the Burkhart Compression building is a compressor manufacturing facility. Lonestar Construction was the builder for the project and Steve Husmann was the head architect. The building utilizes a gable symmetrical framing system, Ultra-Dek® roof system and PBR wall panels.

krosstown-building
Permalink Gallery

Krosstown – Tom Stitt Prosteel STR, LLC

Krosstown – Tom Stitt Prosteel STR, LLC

,

Tom Stitt Prosteel STR, LLC served as the builder for the Krosstown building in Phoenix, Arizona. Steeling Arizona, LLC served as the erector and Hokanson Architects were the architectural team for the building. The 56,000 square foot manufacturing facility has a gable symmetrical frame and utilizes PBR roof and wall panels with a block and stucco finish.

engineered metal building, metal building structure, custom metal buildings, metal mart buildings, pre-engineered metal buildings, metal building systems, custom metal building
Permalink CAID Industries, 2014 Mid-West Structure of the YearGallery

The 2014 Structure of the Year – CAID Industries – Fast Fab Erectors

The 2014 Structure of the Year – CAID Industries – Fast Fab Erectors

,

The CAID Industries project, which was named the 2014 Mid-West Structure of the Year,  is located in Tucson, AZ. Fast Fab Erectors, also of Tucson, was the builder, erector and roofing contractor on the project, and Division II was the general contractor.

CAID Industries is a leader in metal fabrication in the Southwest United States. Their facility includes 20 acres of fenced-in yard and office and production facilities.

CAID’s 54,800 square foot structure is modular rigid frame, 160’ x 240’ with a 40’ eave height. Since it is in an air corridor at Tucson International Airport, the peak height was restricted. Designers used a ½:12 roof slope to obtain the maximum eave height possible, given the height restraints. Ultra Dek was used for the roofing; end wall and sidewall panels are Shadowrib.

The center interior modular rigid frame supports two 30-ton, 60’ bridge cranes; an outside south bay has two 20-ton, 43’bridge cranes. They are located in partition walls with bayonet doors and when the hydraulic single leaf doors are open, there is unrestricted crane movement through the partition walls.

All roll-up doors up to 30’ wide are 22’ tall. It also features 72 skylights, LED light fixtures, brightness activated T-5 fluorescent fixtures, and 5’ wall lights that extend down from the eaves on both sides.

CAID manufactured their own custom gates for the project. They are one-piece metal with the CAID logo cut into the gate design.

Construction began January, 2014 and was completed in May, 2014.

 

 

engineered metal building, metal building structure, custom metal buildings, metal mart buildings, pre-engineered metal buildings, metal building systems, custom metal building
Permalink JAMCo facility, located in Bastrop, TX, is the 2014 Mid-West Steel Building Company Building of the Year. LoneStar Construction, Houston, was the General Contractor.Gallery

2014 Building of the Year – JAMCo – LoneStar Construction

2014 Building of the Year – JAMCo – LoneStar Construction

,

JAMCo (Johnson Architectural Metals Company,) the 2014 Mid-West Steel Building Company Building of the Year, is a multi-building project located in Bastrop. JAMCo, a Georgia-based construction company, built the structure to serve as their Texas regional headquarters. The company furnishes and installs exterior envelopes for high-rise buildings. The project consists of three buildings: a crane building, a warehouse building and an office building.

The 80’ x 200’ x 28’ crane building has a 1:12 roof slope designed for a five-ton top running crane; the beams, brackets, stops and rail were manufactured by Mid-West.

The warehouse building is 80’ x 300’ x 20’ with a 1:12 roof slope. It has wall light transmitting panels at the eaves on the back sidewall and 10’ long ridge vents. The roof of the crane and warehouse buildings is PBR Galvalume; the walls are Signature 300 PBR in Tundra and trim is Hawaiian Blue.

The office building is 47’-4” by 59’-5-1/2’ by 27’-0” (low side and 27’-11-13/16 (high side.) The roof is “B” deck for a TPO (thermoplastic polyolefin) roof installed by others. The walls were left open to receive 8” thick glass panels fabricated by JAMCo. The building has a full mezzanine with decking and joists by Mid-West. Accessories included back wall light transmitting panels.

LoneStar Construction of Houston was the General Contractor. L & Y Construction of Houston was the erector and roofing contractor. Husman Architecture PLLC, Houston, and JAMCo were the designers.

 

 

Mid-West, Mid-West Steel Building Company, Mid-West Steel, engineered metal building, metal building structure, custom metal buildings, metal mart buildings, pre-engineered metal buildings, metal building systems, custom metal building
Permalink Gallery

Phoenix – Clay Development & Construction

Phoenix – Clay Development & Construction

, ,

Phoenix is a 2014 Mid-West Design Build Excellence Award winner. Phoenix, a Houston-based horizontal and directional drilling company,  required large areas unobstructed by support columns in their 112,500 square foot building.

To meet their needs, they utilized the patented Long Bay framing system to create 65’ interior bays. Long Bay had previously been used to create 60’ interior bays. For the Phoenix project, engineers were able to design a structure that would accommodate 65’ clear span bays, a first for the Long Bay system.

Clay Development and Construction was the General Contractor and designer. Amalda Enterprises was the erector and roofing contractor. Roof panels were Double-Lok® on a ½:12 roof slope. End wall and sidewalls were PBR and tilt wall.

 

Mid-West, Mid-West Steel Building Company, Mid-West Steel, steel buildings, metal buildings, pre-engineered steel buildings, custom designed metal buildings
Permalink The 120,000 square foot General Plastics and Composites building, located in Houston, houses an office building, manufacturing plant and materials warehouse area. The office area is 15,000 square feet, the manufacturing area is 67,500 square feet and the materials area is 37,500 square feet. The building features Ultra-Dek roof panels on a 1:12 slope and EIFS endwall and sidewall panels. General Contractor was Houston-based GRA – Gulf Coast Construction; Amalda Enterprises, Inc. was the erector and roofing contractor and Joe Milton Architects was the designer. Steel products supplied by Mid-West Steel Building Company.Gallery

General Plastics and Composites – GRA Gulf Coast Construction

General Plastics and Composites – GRA Gulf Coast Construction

,

The 120,000 square foot General Plastics and Composites building, located in Houston, houses an office building, manufacturing plant and materials warehouse area. The office area is 15,000 square feet, the manufacturing area is 67,500 square feet and the materials area is 37,500 square feet. The building features Ultra-Dek roof panels on a 1:12 slope and EIFS endwall and sidewall panels. General Contractor was Houston-based GRA – Gulf Coast Construction; Amalda Enterprises, Inc. was the erector and roofing contractor and Joe Milton Architects was the designer.